Blackjack Roller Head Pipe Jack Stand - 103BJS

• Adjustable Height: Min.- 29″ Max.- 46″
• Quick Slip Tube Adjustment
• Fine Screw Adjustment
• Adjusting Screw 1 3/8″-5 Pitch Full Acme Thread
• “T” Handle Lock For Slip Tube ½”-13 Thread
• Adjusting Nut Length 1 to 1½” With Balance Ball Ends For Easy Adjusting
• Certified Testing By Independent Source
• All Stands Have Safety Instructional Label & Load Capacity Label With 2 to 1 Safety Factor
• Rollers 4″ Dia. x ½” A 36 Steel Lathe Turned For Concentricity
• Rollers Have Oilless Bronze Bushings
• Bases Accept: V Head, Roller Head, Transfer Ball & Bar Stock Roller Head
• Built In Stop For Slip Tube To Prevent Injury
• Washer Face On Slip Tube For Smoother Screw Adjustment
• Legs Are 1″ Square Tube 16 Gauge Wall Thickness
• All Legs Have 2″ Diameter Foot Surface
• Safety Washer Retainer Finger Formed From 12 Gauge Steel Sheet
• Safety Washer Has “EZ” Lift Release Tab
• Safety Washer Has Retainer Pin to prevent Loss Of Washer
• Safety Washer “Fall Proof” Design Prevents Slippage Prior To Tightening “T” Handle
• Rollers Painted With High Visibility Yellow Paint
• Roller Head Will Accept Work Piece Up To 12″ Diameter
• Working Load Capacity For Roller Head Jack Stands Is 2500 Lbs.
• Complete Stand With Roller Head Weighs 23 Lbs.
• Stand has Powder Coat Finish

Adjustable Roller Pipe Jack Welding Stand - BJS106

• Roller Adjustment From Either End Of Carriage With 1 ¼ Hex Nuts
• Rollers 5/8 x 4” Diameter Cast Iron Lathe Turned For Concentricity
• Working Height 30 ¾” at Center Line of Rollers
• Roller Holders Are Made Of Cast Steel
• Adjusting Screw 3/4″ – 6 Pitch Full Acme Thread
• Adjusting Screw Mounted in Oil Lite Bronze Bushings
• Cariage Housing 2” x 3” 11 Gage Tubing
• Leg Pattern 23” x 26” For Working Stability
• Legs Are Of “A” Frame Design
• Center Braces From Middle of Carriage To Lower Leg Brace For Even Distribution Of Load
• All Legs Have 2” Diameter Foot Surface
• Adjustment Of Rollers Will Accept 1/2″ – 48” Diameter Work Piece
• Roller Holders Have Drain Passages To Prevent Trapped Water If Used Outdoors
• Carriage Housing Has Drain Holes to Allow Water To Drain Through Legs
• Legs & Braces 1” Square Tube 16 Gage
• Rollers Are Powder Coated With High Visibility Safety Yellow
• All Stands Are Labeled With Working Capacity Of At Least 2 to 1 Safety Factor
• Certified Testing By Independent Source
• Working Load Capacity 6,000 LBS
• Complete Stand Weighs 32 LBS.
• Stand has Powder Coat Finish

V-Roller Pipe Jack Welding Stand - BJS122

Specifications coming soon. Call for details.

Bar Stock Pipe Jack Stand - Model: 104BJS

• Adjustable Height: Minimum 32” Maximum 46”
• Certified Testing By Independent Source
• All Stands Have Safety Instructional Label & Load Capacity Label With 2,1 Safety Factor
• Bases Accept V Head, Roller Head, Transfer Balls, & Bar Stock
• Built In ‘Stop’ For Slip Tube To Prevent Injury
• Washer Face On Slip Tube For Smoother Screw Adjustment
• Legs Are 1” Square Tube 16 Gage Wall Thickness
• All Legs Have 2” Diameter Foot Surface
• Safety Washer Retainer Finger Formed From 12 Gage Steel Sheet
• Safety Washer Has “EZ” Lift, Release Tab
• Safety Washer Has Retainer Pin To Prevent Loss Of Washer
• Safety Washer “Fall Proof” Design Prevents Slippage Prior To Tightening “T” Handle
• Bar Stock Roller Head Painted With High Visibility Yellow Paint
• Working Load Capacity for Bar Stock Roller Head Stands 2,500 Lbs.
• Complete Stand With Bar Stock Head Weighs 20 Lbs.
• Stand has Powder Coat Finish